{"id":2945,"date":"2026-10-21T02:48:47","date_gmt":"2026-10-21T02:48:47","guid":{"rendered":"https:\/\/fschier.com\/?p=2945"},"modified":"2026-10-21T02:48:48","modified_gmt":"2026-10-21T02:48:48","slug":"window-handle-base-dimensions-why-rosette-size-and-support-lugs-matter","status":"publish","type":"post","link":"https:\/\/fschier.com\/pl\/window-handle-base-dimensions-why-rosette-size-and-support-lugs-matter\/","title":{"rendered":"Window Handle Base Dimensions: Why Rosette Size and Support Lugs Matter"},"content":{"rendered":"<p class=\"wp-block-paragraph\">A window handle can have the right lever, the right finish and the right spindle, and still be the wrong part. The reason is often the base: the rosette, backplate or fixing lugs that locate the handle on the sash. Base dimensions decide whether the screw holes line up, whether the body clears the profile and gasket, and whether the drive sits where the mechanism expects it. For importers, OEM buyers and window fabricators, a mismatch rarely shows up on a catalogue page. It shows up at installation, or months later as a loose, rocking handle. This article explains which base dimensions to control, how rosette and lug designs change the specification, and what to send a supplier so the quotation matches the part you need.<\/p>\n\n\n\n<h2 id=\"what-does-the-base-of-a-window-handle-actually-do\" class=\"wp-block-heading\">What Does the Base of a Window Handle Actually Do?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The base does four jobs. It locates the handle relative to the spindle or drive. It fixes the handle to the sash through screws. It covers the fixing holes and the profile cut-out. It also sets how far the lever stands off the surface. Each job has its own dimensions, which is why &#8220;same size&#8221; is not a usable specification.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Terminology varies between suppliers, so define it in your drawing:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Rosette or rose:<\/strong> a round or oval cover and seating around the pivot. It may be screw-through or a snap-on cover over concealed screws.<\/li>\n\n\n\n<li><strong>Backplate:<\/strong> a longer plate, usually narrow, that carries the fixing holes above and below the pivot.<\/li>\n\n\n\n<li><strong>Support lugs or fixing tabs:<\/strong> separate raised or rear-projecting ears that carry the screws, instead of one continuous plate.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">A single product can combine these. A handle may have a circular pivot cover on a narrow plate, or a wide enclosed body with two rear tabs. If a buyer writes &#8220;rosette&#8221; and the supplier reads &#8220;backplate&#8221;, the quotation can be for a different part.<\/p>\n\n\n\n<div class=\"wp-block-greenshift-blocks-image gspb_image gspb_image-id-gsbp-3811069\" id=\"gspb_image-id-gsbp-3811069\"><img decoding=\"async\" src=\"https:\/\/fschier.com\/wp-content\/uploads\/2026\/10\/Window-Handle-Base-Dimensions-Why-Rosette-Size-and-Support-Lugs-Matter-2.jpg\" data-src=\"\" alt=\"Window Handle Base Dimensions Why Rosette Size and Support Lugs Matter\" loading=\"lazy\" width=\"1000\" height=\"1000\" title=\"\"><\/div>\n\n\n\n<h2 id=\"which-base-dimensions-decide-whether-a-handle-fits\" class=\"wp-block-heading\">Which Base Dimensions Decide Whether a Handle Fits?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Four dimension groups control mechanical fit, and the fastener and substrate control how well it holds. Spindle length is a separate interface, covered later.<\/p>\n\n\n\n<h3 id=\"fixing-centres\" class=\"wp-block-heading\">Centra mocuj\u0105ce<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Fixing centres are the distance between the centres of the screw holes. They are the first dimension replacement buyers check, and the one most often oversimplified. One retailer guide states that <a href=\"https:\/\/www.homesecureshop.co.uk\/blogs\/news\/are-upvc-window-handles-standard-size-guide-tips\" target=\"_blank\" rel=\"noopener\">most modern espag uPVC handles use 43 mm screw centres<\/a>, while also warning that spindle length and handle type vary. Another lists <a href=\"https:\/\/www.windowhardwarestore.com\/blog\/espag-window-handle-sizes-spindle-length-and-screw-centres\" target=\"_blank\" rel=\"noopener\">43 mm, 70 mm, 90 mm and 92 mm screw centres<\/a> across espag and cockspur handles and notes that surface-mounted roses and fixed backplates may differ.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Treat 43 mm as a common reference, not a rule. Older and bespoke profiles use other values. A four-hole base adds a second axis: the spacing between the two holes in each pair, plus the spacing between pairs. Measure from hole centre to hole centre, as <a href=\"https:\/\/www.windowhardwarestore.com\/blog\/how-to-measure-an-espag-handle-for-replacement\" target=\"_blank\" rel=\"noopener\">measurement guidance for espag handles<\/a> points out, not from the outer edges of the plate.<\/p>\n\n\n\n<h3 id=\"base-footprint-and-edge-clearance\" class=\"wp-block-heading\">Base footprint and edge clearance<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Footprint means overall length, width, corner radius and the distance from the spindle centre to each end of the base. It decides whether the base overlaps a glazing bead, gasket, sash edge or adjacent hardware. A slightly larger rosette can cover an old screw pattern, which is useful in refurbishment. The same extra width can foul a bead or leave the handle sitting off-flat.<\/p>\n\n\n\n<h3 id=\"seating-depth-and-rear-features\" class=\"wp-block-heading\">Seating depth and rear features<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A base that looks flat from the front may have rear tabs, a raised drive boss or a standoff. These set how the handle seats against the sash and how far the drive projects. Where the screws pass through the sash, check that screw heads and shanks clear internal beading and seals when the window closes.<\/p>\n\n\n\n<h3 id=\"drive-position-and-handing\" class=\"wp-block-heading\">Drive position and handing<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The drive may sit at the centre of the base or offset from it. A handed lever also has a nose or arm whose position depends on left or right hand. A mirrored part is a different part for the mechanism that receives it.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Wymiar<\/th><th>Co nagra\u0107<\/th><th>Typical failure if wrong<\/th><th>What to verify with the supplier<\/th><\/tr><\/thead><tbody><tr><td>Centra mocuj\u0105ce<\/td><td>Centre-to-centre, both axes for four-hole bases<\/td><td>Holes do not align; handle cannot be fixed or sits skewed<\/td><td>Drawing with the pattern dimensioned and a tolerance stated<\/td><\/tr><tr><td>Base footprint<\/td><td>Length, width, corner radius, spindle-to-end distances<\/td><td>Fouls bead, gasket or sash edge; exposes old holes<\/td><td>Overlay drawing on the profile section<\/td><\/tr><tr><td>Seating and rear features<\/td><td>Tab position, boss height, drive projection<\/td><td>Rocking, base not flush, drive bottoms out<\/td><td>Rear and side views with projection dimensions<\/td><\/tr><tr><td>Drive position and handing<\/td><td>Drive offset, section, hand, nose position<\/td><td>Lever strikes frame; nose misses its keeper<\/td><td>Sample trial on the actual sash<\/td><\/tr><tr><td>Fastener and substrate<\/td><td>Screw type, length, what the screw bites into<\/td><td>Stripped threads, crushed thin frame<\/td><td>Screw specification and recommended fixing method<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<div class=\"wp-block-greenshift-blocks-image gspb_image gspb_image-id-gsbp-7110e14\" id=\"gspb_image-id-gsbp-7110e14\"><img decoding=\"async\" src=\"https:\/\/fschier.com\/wp-content\/uploads\/2026\/10\/Window-Handle-Base-Dimensions-Why-Rosette-Size-and-Support-Lugs-Matter-3.jpg\" data-src=\"\" alt=\"Window Handle Base Dimensions Why Rosette Size and Support Lugs Matter\" loading=\"lazy\" width=\"1000\" height=\"1000\" title=\"\"><\/div>\n\n\n\n<h2 id=\"how-do-rosettes-backplates-and-split-lugs-compare\" class=\"wp-block-heading\">How Do Rosettes, Backplates and Split Lugs Compare?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Base style changes what has to be specified. The table below is a qualitative comparison, not performance data.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Base style<\/th><th>How it is fixed<\/th><th>Where the fit risk sits<\/th><th>Typical buyer question<\/th><\/tr><\/thead><tbody><tr><td>Narrow backplate, exposed fixings<\/td><td>Screws through the plate above and below the pivot<\/td><td>Hole centres; plate length against the profile<\/td><td>Do the centres match the existing holes?<\/td><\/tr><tr><td>Narrow plate with round pivot cover<\/td><td>Exposed or accessible fixings plus a circular cover<\/td><td>Cover diameter; plate overhang<\/td><td>Does the cover hide or expose the old pattern?<\/td><\/tr><tr><td>Split lugs (no continuous plate)<\/td><td>Two raised lugs, each with a hole pair<\/td><td>Lug spacing, lug height, nose clearance<\/td><td>Is the lug-to-lug distance matched, not only the hole pair?<\/td><\/tr><tr><td>Wide concealed body with rear tabs<\/td><td>Tabs fixed behind the body<\/td><td>Body width and depth; tab position; drive post<\/td><td>Does the body clear the profile, and does the tab pattern match?<\/td><\/tr><tr><td>Round rose with screw-through or snap-on cover<\/td><td>Screws under a cover or through the rose<\/td><td>Rose diameter; cover fixing method<\/td><td>Is it screw-through or concealed, and who supplies the screws?<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">The three CHIER product pages reviewed for this article illustrate how different these structures are. The <a href=\"https:\/\/fschier.com\/pl\/produkt\/uchwyt-okienny-z-uchwytem-z-dzielona-podstawa-montazowa-z-czterema-otworami\/\">handed window lever handle with a split four-hole mounting base<\/a> uses two raised fixing lugs above and below the pivot, each with a pair of holes, rather than a continuous backplate. The page lists mounting centres, lug spacing, overall base height, nose projection and handing as items to check, because the nose must align with the receiving component through the full movement.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The <a href=\"https:\/\/fschier.com\/pl\/produkt\/zakrzywiona-klamka-okienna-z-podwojnymi-tylnymi-uchwytami-montazowymi\/\">zakrzywiona klamka okienna z podw\u00f3jnymi tylnymi uchwytami monta\u017cowymi<\/a> is a different case: a wide enclosed body with two metal tabs at the rear and a projecting cylindrical drive post between them. Body width and depth, tab spacing, and post diameter and projection matter more than the outline seen from the front. By contrast, the <a href=\"https:\/\/fschier.com\/pl\/produkt\/dluga-zakrzywiona-klamka-okienna-z-waska-podstawa-z-czterema-otworami\/\">long curved window handle with a narrow four-hole base<\/a> leaves its four fixing recesses exposed. It extends the plate above and below a circular pivot cover, so the fixing-centre pattern and the rectangular drive geometry carry the fit.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">None of these should be matched by photograph. Each needs a dimensioned drawing or a physical sample.<\/p>\n\n\n\n<h2 id=\"does-a-larger-rosette-make-a-window-handle-stronger\" class=\"wp-block-heading\">Does a Larger Rosette Make a Window Handle Stronger?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Not by itself. A larger rosette or wider base is often assumed to mean a sturdier handle. Under load, the handle is held by its fasteners, and the load goes into whatever they bite into. Depending on the profile, that may be a steel reinforcement or metal insert behind a thin sash wall. So fixing positions, fastener type and substrate condition usually matter more than how much surface the plate covers.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">What a larger base does provide is cosmetic coverage, a larger bearing area against the profile, and a way to hide old holes in refurbishment. The cost is a bigger footprint and more chance of interference. Trade-offs also run the other way. Widely spaced lugs may resist rocking better than a compact rose, as a matter of general mechanical reasoning. That depends on the profile and fixings, and should be tested on the actual assembly rather than assumed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Thin or soft substrates change the picture. One retailer guide suggests using <a href=\"https:\/\/www.windowhardwarestore.com\/blog\/how-to-measure-an-espag-handle-for-replacement\" target=\"_blank\" rel=\"noopener\">packers behind the backplate on aluminium or thin frames<\/a> to prevent crushing and keep screw torque even. That is a fixing issue, not a size issue. Ask a supplier what the base is expected to bear on and which screw is recommended, instead of asking only how large the base is.<\/p>\n\n\n\n<h2 id=\"how-do-base-dimensions-interact-with-the-spindle-handle-type-and-standards\" class=\"wp-block-heading\">How Do Base Dimensions Interact With the Spindle, Handle Type and Standards?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Spindle.<\/strong> The base positions the handle; the drive transmits torque. A correct base with the wrong drive length still fails, and the reverse is also true. The detailed failure modes are covered in this guide to <a href=\"https:\/\/fschier.com\/pl\/w-jaki-sposob-dlugosc-trzpienia-klamki-okiennej-wplywa-na-to-ze-zarowno-zbyt-krotki-jak-i-zbyt-dlugi-trzpien-nie-spelniaja-swojej-funkcji\/\">why spindle length that is too short or too long fails<\/a>. When the base seats before the spindle bottoms out, the screws are clamping the handle rather than fighting an interference.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Handle type.<\/strong> A base specification depends on what sits behind it. Cam, espag, fork and spindle-drive handles have different interfaces, so the same base outline can be right for one and wrong for another. The comparison of <a href=\"https:\/\/fschier.com\/pl\/rodzaje-klamek-do-okien-skrzydlowych-krzywkowe-espagowe-widelkowe-oraz-z-napedem-trzpieniowym\/\">cam, espag, fork and spindle-drive casement handle types<\/a> helps identify the drive before dimensions are frozen.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Standards.<\/strong> The <a href=\"https:\/\/knowledge.bsigroup.com\/products\/building-hardware-hardware-for-windows-and-door-height-windows-requirements-and-test-methods-handles-primarily-for-tilt-and-turn-tilt-first-and-turn-only-hardware\" target=\"_blank\" rel=\"noopener\">BSI record for BS EN 13126-3:2023<\/a> shows that the standard covers durability, strength, security and functionality of window handles. It does not specify a universal base size. Its scope also excludes handles with a handle length over 170 mm, measured as defined in the standard. For a long-lever handle, ask the supplier which length applies and which test basis they are quoting. Buyers who want to read a quoted classification string can follow the <a href=\"https:\/\/fschier.com\/pl\/en-13126-klasyfikacja-klamek-okiennych-jak-odczytywac-kod\/\">EN 13126-3 handle classification code guide<\/a>. A classification code does not confirm that your fixing centres match.<\/p>\n\n\n\n<h2 id=\"what-are-the-most-common-base-dimension-mistakes\" class=\"wp-block-heading\">What Are the Most Common Base-Dimension Mistakes?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Ordering from a front photograph.<\/strong> Rear tabs, bosses and fixing positions are not visible from the front.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Measuring to the plate edge.<\/strong> Edge-to-edge dimensions describe the plate. Hole centre to hole centre describes the fit.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Assuming 43 mm.<\/strong> It is common, not universal, and a four-hole base has more than one spacing to check.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Matching one axis only.<\/strong> On a split-lug or four-hole base, the lug-to-lug distance and hole-pair spacing are separate dimensions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Ignoring clearance.<\/strong> A base that fits the screws can still foul the bead, gasket, sill or adjacent hardware during rotation.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Approving a sample with no dimension record.<\/strong> Without a measured reference, later batches cannot be checked against it.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Consider an illustrative scenario, not a real customer case. A distributor replaces a discontinued handle that had a narrow plate with a similar-looking one on a wider concealed body. The screw centres match, so the first sample is approved from a bench check. On site, the wider body sits against the bead and cannot seat flat, so the installer tightens the screws to pull it down and the lever feels stiff. The cause was not a defect. The dimension that mattered, body width against bead clearance, was never in the specification.<\/p>\n\n\n\n<div class=\"wp-block-greenshift-blocks-image gspb_image gspb_image-id-gsbp-b61ddfe\" id=\"gspb_image-id-gsbp-b61ddfe\"><img decoding=\"async\" src=\"https:\/\/fschier.com\/wp-content\/uploads\/2026\/10\/Window-Handle-Base-Dimensions-Why-Rosette-Size-and-Support-Lugs-Matter-4.jpg\" data-src=\"\" alt=\"Window Handle Base Dimensions Why Rosette Size and Support Lugs Matter\" loading=\"lazy\" width=\"1000\" height=\"1000\" title=\"\"><\/div>\n\n\n\n<h2 id=\"what-should-buyers-specify-before-requesting-a-quote\" class=\"wp-block-heading\">What Should Buyers Specify Before Requesting a Quote?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A complete RFQ lets the supplier confirm fit before tooling or sampling. Send as many of these as you can:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li><strong>Front, side and rear drawings<\/strong> with fixing centres, base length and width, corner radius and drive projection dimensioned. Where lugs are used, include lug-to-lug distance and lug height.<\/li>\n\n\n\n<li><strong>A physical sample<\/strong> when the pattern cannot be documented accurately. CHIER&#8217;s product pages ask for a dimensioned drawing or a sample, and recommend a sample when the fixing pattern is hard to document.<\/li>\n\n\n\n<li><strong>Drive details:<\/strong> section, length, position relative to the base, and any offset.<\/li>\n\n\n\n<li><strong>Handing and rotation:<\/strong> left, right or reversible, plus operating direction and the receiving component.<\/li>\n\n\n\n<li><strong>Installation photographs<\/strong> showing the profile section, bead and gasket position, and any adjacent hardware.<\/li>\n\n\n\n<li><strong>Fastener information:<\/strong> screw type and length, and what they bite into.<\/li>\n\n\n\n<li><strong>Tolerance expectations<\/strong> on fixing centres and drive position, agreed rather than assumed.<\/li>\n\n\n\n<li><strong>Finish, colour, quantity and packaging<\/strong>, including how handed pairs are separated.<\/li>\n\n\n\n<li><strong>Target market and compliance needs,<\/strong> including the EN 13126-3 classification you require, if any.<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">Ask for a first-article dimension report and fit trial on the actual sash before approving production. Keep the approved sample as the reference for later batches. Buyers with a custom base or lug layout should also request MOQ, lead time and tooling terms in writing rather than assuming them.<\/p>\n\n\n\n<h2 id=\"frequently-asked-questions\" class=\"wp-block-heading\">Cz\u0119sto zadawane pytania<\/h2>\n\n\n\n<h3 id=\"what-are-the-base-dimensions-of-a-window-handle\" class=\"wp-block-heading\">What are the base dimensions of a window handle?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">They are fixing centres, overall base length and width, corner radius, seating depth, drive position and, for lugged designs, lug spacing and height. Measure hole centre to hole centre, not plate edges, and record handing.<\/p>\n\n\n\n<h3 id=\"what-does-a-window-handle-rosette-do\" class=\"wp-block-heading\">What does a window handle rosette do?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A rosette locates the handle around the pivot, covers the cut-out and sometimes hides the fixing screws. It may be screw-through or a snap-on cover. Its diameter affects appearance and clearance, but fastener position and substrate usually govern holding strength.<\/p>\n\n\n\n<h3 id=\"are-window-handle-screw-centres-standard\" class=\"wp-block-heading\">Are window handle screw centres standard?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Not universally. Retailer guides commonly cite 43 mm for espag handles, but 70 mm, 90 mm and 92 mm also appear, and older or bespoke profiles differ. Measure the installed handle rather than relying on a standard.<\/p>\n\n\n\n<h3 id=\"what-are-support-lugs-on-a-window-handle\" class=\"wp-block-heading\">What are support lugs on a window handle?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Support lugs are raised or rear-projecting fixing tabs that carry the screws instead of a continuous backplate. They must be matched on lug spacing, hole pattern and height, because the handle cannot sit correctly if either differs.<\/p>\n\n\n\n<h3 id=\"can-a-bigger-backplate-cover-old-screw-holes\" class=\"wp-block-heading\">Can a bigger backplate cover old screw holes?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">It can, and this is a common refurbishment tactic. Check that the larger base does not foul the bead, gasket or sash edge, and that the drive position and handing still match the existing mechanism.<\/p>\n\n\n\n<h3 id=\"does-en-13126-3-set-handle-base-dimensions\" class=\"wp-block-heading\">Does EN 13126-3 set handle base dimensions?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">No. The standard addresses durability, strength, security and functionality of handles, not a standard base size. Confirm fixing centres, footprint and drive geometry through drawings, samples and fit trials, whatever classification code is quoted.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>","protected":false},"excerpt":{"rendered":"<p>How rosette size, fixing centres and support lugs decide whether a window handle fits, and what B2B buyers should specify before requesting an OEM quote.<\/p>","protected":false},"author":1,"featured_media":2946,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_gspb_post_css":"#gspb_image-id-gsbp-3811069 img,#gspb_image-id-gsbp-7110e14 img,#gspb_image-id-gsbp-b61ddfe img{vertical-align:top;display:inline-block;box-sizing:border-box;max-width:100%;height:auto}","footnotes":""},"categories":[17],"tags":[1268,127,1650,1647,1648,1649],"class_list":["post-2945","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-window-door-hardware-design","tag-fixing-centres","tag-oem-window-hardware","tag-replacement-window-handles","tag-rosette-size","tag-support-lugs","tag-window-handle-base"],"_links":{"self":[{"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/posts\/2945","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/comments?post=2945"}],"version-history":[{"count":1,"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/posts\/2945\/revisions"}],"predecessor-version":[{"id":2950,"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/posts\/2945\/revisions\/2950"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/media\/2946"}],"wp:attachment":[{"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/media?parent=2945"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/categories?post=2945"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/fschier.com\/pl\/wp-json\/wp\/v2\/tags?post=2945"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}